A “P” will be displayed when the pump is not on, to indicate that the water near the temperature sensors must be purged to get an accurate reading of the water temperature. To display the water temperature when “P” is showing on the display, press the “JETS” button. After 2 minutes, the water temp will be displayed.
How do I reset my Softub?
Your Softub features a patented combination lock located at the end of the fastening straps with the lock preset to open at 0-0. To reset the combination to your own number, first open the buckle, then use a pointed object, such as a ballpoint pen, to press in the reset button.
Where is the reset button on a Softub?
If there are no lights on the Softub’s control panel, check the ground fault circuit interrupter (GFCI) socket that the Softub is plugged into. The socket should have three prongs and two buttons on it. Press both the top button (the “reset” button) and the bottom button (the “test” button).
Why is my Softub not heating?
A: The unit will heat as the motor runs; this can take close to 48 hours when you first fill the tub with cold water. If your motor is running, it is heating as well. If the unit is not heating to the correct temperature, it is likely there is an issue with the temperature probes in the motor unit.
Why does my Softub keep turning on and off?
It sounds like the temperature sensor is getting cold, triggering a call for heat, then turning it off as soon as the pump moves some warmer water in to the equipment.
What does the P mean on my soft tub?
Your Softub® will automatically display the temp of the water in your spa, whenever the pump is on and has been running for 2 minutes continuously. A “P” will be displayed when the pump is not on, to indicate that the water near the temperature sensors must be purged to get an accurate reading of the water temperature.
What does SP1 mean on my Softub?
When the Special Temperature Mode is active the display will flash “SP1” every 5 seconds to indicate that you are in this mode. OVERNIGHT MODE. Overnight Mode will put the tub in standby for 12 hours a day and allow it to operate normally for the other 12 hours.
How do you fix a Softub?
Contact your Softub dealer to have them send you a vinyl repair kit if you notice any leaks in the liner of your tub. To fix a hole in the liner you will need to drain the tub to access the tear in the liner. Once the liner is dry, apply the adhesive to the application wand and then apply the adhesive to the patch.
How do you shock a Softub?
Chemical Instructions for your Softub using granular chlorine & a Spa Frog Mineral Cartridge.
How do you turn on a Jets Softub?
When the tub water is at the set temperature, the jets will not be on. If you wish to use the tub, the “JETS” button on the control panel activates a timer that overrides the temperature you have selected. This turns the jets on for a 15 minute period.
How long does a Softub last?
Depending on your water source, the Softcare Gon (metal & scale remover) should last about two months. Once your Softub Spa Frog® mineral purifier is exposed to water, it is active for four months only.
How does a soft tub heater work?
The Softub is made of a soft, squeezable polypropylene foam, and covered with LeatherTex, a marine-grade vinyl. How is the water heated? The hot tub water is heated using a patented heat recovery system, which uses waste heat from the motor to heat the water.
Can you use a soft tub in the winter?
Softub is ideal for winter. Softub is the ultimate in portable hot tubs, and can be moved season to season easily. Roll in to place, connect, and fill.
Why is my hot tub surging?
A surging hot tub pump happens when the pump in your hot tub stops functioning as designed. The problem is usually diagnosable by the pulsating of the hot tub pump. The cause of a surging pump relates to filter problems, water levels, clogged lines, airlocks, and worn-out pumps.
Why does my hot tub turn on by itself?
They take into account the temperature, sensing when it falls below a certain level and starting heating. Therefore, when a hot tub is in automatic mode, the timer will start or stop heating when it is necessary, so you don’t have to worry about turning your place on and off according to temperature.
Post navigation
ncG1vNJzZmismJq2r7LIp6CtnZuewaS0xKdlnKedZLS2tcOeZqudkZmys7%2BMmqqkZaedrrV5w6icrGWgYrqmrc1mpqdlo6SztcHBZpuiq6Chrrp7